CCH0123F1-Z03A | Ingmar's Retroblog

An interesting problem has arisen with the measurement technology in the laboratories at my workplace. I use the term “measurement technology” to describe the equipment of a laboratory workstation for basic training. There are a total of nineteen laboratory workstations, each equipped with two laboratory power supplies, two desktop multimeters, a Keysight signal generator and a Keysight (Agilent) oscilloscope of the Infiniivision DSO-X 20xx series. All devices are network-compatible and are connected to the corresponding workstation computer via LAN. This means that the measuring devices can be accessed using different software (Agilent VEE, Matlab, LabVIEW etc.). The devices were purchased around three years ago and replace the almost twenty-year-old laboratory equipment.

However, it has now happened that the DSO-X2012A oscilloscope at one workstation no longer showed any signs of life. It occasionally happens that during laboratory exercises or when working freely in the laboratories, a student presses the emergency stop switch of the workstation and thus de-energizes it. But this was not the case. All the devices connected to the workstation worked, with the exception of the DSO. Voltage could also be measured at the end of the IEC plug. So the problem could only be with the oscilloscope itself. The rear panel is quickly unscrewed, a shield plate removed and the power supply unit is exposed. The first visual inspection immediately revealed the large filter capacitor with its upwardly curved cap. But first things first.

The mains voltage was measured at the AC pins of the mains input, but no DC voltage was measured at any of the outputs of the power supply unit. Regardless of whether the power switch of the device was switched on or off. This suggests that the power supply unit is defective.

First, the power supply unit was removed and examined, starting with the AC input side. The print fuse in the area of the mains filter was the first defective component to be noticed. It is a slow-blow 6.3A/250V fuse. As a blown fuse always has a reason to switch off, the search continued. The mains rectifiers were OK, but the 100uF / 420V electrolytic capacitor, which is used to smooth the DC voltage on the primary side, had already suffered some thermal damage and was bloated.

original electrolytic capacitor 100uF /420V /105°C

Its capacity was also no longer within the nominal range. But even that was not the direct reason for the fuse blowing. This was quickly found. A mosfet used to control the transformer was low-resistance. More precisely, it had a short circuit between all the connections.

The following picture shows the installation positions of the components. These have been replaced. The mosfet was replaced with an original type and the power supply capacitor was replaced with a 100uF / 450V / 105°C type. Although it is about five millimeters higher, it fits easily into the power supply unit.

Installation position of the capacitor and the mosfet

Two SMD resistors on the back of the power supply board were defective in the area of the gate connection of the mosfet. These were an SMD resistor of size 0805 with 5.11 Ohm and an SMD resistor of size 1206 with 2.0 kOhm. The picture below also shows the installation position.

Mounting position of defective SMD resistors

After all the components mentioned had been replaced, a first functional test was carried out. However, this was sobering, as the power supply unit was still not working. The fuse remained intact and the DC voltage on the primary side was stable. But the gate of the mosfet was not activated – unfortunately. Because now came the time-consuming part of the repair. On the power supply board, installed upright, there is another board on which several controller ICs are installed. If you follow the gate line from the Mosfet, it ends at a pin on this control board. So this must be removed.

To do this, the cooling plate had to be removed first. Then it became a bit tedious, because the controller board is not connected to the main board via a pin header or plug connection, but the contact pins are laid out and milled out. This means that the desoldering work has to be carried out very carefully so as not to damage the conductor tracks at the ends of the milled pins.

Once the removal was successfully completed, the controller board could be inspected. Lo and behold, the line routed from the gate of the mosfet ends at pin 6 of a small IC. This is a UC3842B VD1R2G. The housing of this IC was blown up. In addition to the controller IC, a SOT23 PNP transistor (PMBT 2907A) was also dead and had a low resistance on all pins.

Installation position of the defective components

After replacing the defective components, the power supply unit was reassembled and a function test was carried out. The oscilloscope started up again and the power supply unit did its job.

It would now be interesting to find out why the power supply gave up the ghost after just three years. Especially as the oscilloscopes do not run continuously, but are only switched on during the relevant courses. We noticed the following: The oscilloscope is permanently connected to the power supply. However, the oscilloscope’s power switch does not switch off the AC supply, but only the controller control in the secondary area of the power supply unit. This means that the power supply unit operates in standby mode when it is switched off. And we have noticed that all oscilloscopes that are switched off have a power loss in standby that heats up the mosfets and especially the 100uF electrolytic capacitor. This would explain the bloated, dried-out electrolytic capacitor and the subsequent death of the power supply units. To verify this, the temperature of the components was measured on several devices that had not been switched on for days.

Thermal sensor on the electrolytic capacitor surface

The following could be determined here. Both the surface of the capacitor and the cooling plate of the mosfets measured temperatures of 56°C to almost 60°C when switched off. Should this be the case?

Temperature measurement on the electrolytic capacitor

Here are the required components:

resistor 5R11 0,1W 0,1% Farnell Nr.: 1872688
resistor 2k0 0.66W Farnell Nr.: 721-9844
PNP Transistor SOT23, SMD Stempel 2F Type PMBT2907A, 215 Farnell Nr.: 1626500
PWM Controller IC, UC3842B VD1R2G / 500kHz Farnell Nr.:2845218
capacitor 100uF / 105°C / 450V
fuse T6.3A 250V

Jun2019: Order numbers updated

In an old post from 2019 I reported about oscilloscopes from the manufacturer Keysight and their problem with a sudden failure. (see link). At that time, it was about oscilloscopes suddenly refusing to work – sometimes with a bang and subsequent smell of “power”. Or simply nothing happened at all after switching on. The reason was and is always the failure of the installed 12VDC power supply CCH0123F1-Z03A. The oscilloscope is designed in such a way that the power supply is still connected to the mains when the “main switch” of the oscilloscope is switched off and is operated in standby mode. The push button switch located on the front panel of the unit then switches the power supply into PowerON mode and 12V power on.

If the devices in the laboratories are permanently connected to live sockets, it is not surprising that the devices age faster than the good old boxes with the cathode ray tubes. The parts, which fall victim to the permanent power supply by thermal continuous load, I have, as well as also the repair expenditure in the contribution at that time represented. On the part of the distributing companies also a reordering or a replacement delivery of new power supplies is not intended or desired. If the devices fail within the warranty period, the replacement by the manufacturer is no problem. If the devices fail after a few years in the laboratory or workshop (it doesn’t matter if they are in use every day, or just stand around plugged in and switched off), then a normal repair service process is carried out by the manufacturer. There are then also the proper tariffs for the service of measurement technology to pay.

In the picture above: “new Meanwell Powersupply” below: “original Lineage Power”.

The power supplies are quite easy to repair, as described in the old report. However, the repair is also quite time-consuming. Of course, it is faster to install a new power supply. Unfortunately, the distributors of the Keysight oscilloscopes do not offer spare parts support and I could not find a direct supplier of the original Lineage power supply. But there is another alternative: In the forum of the EEV blog some users have found alternative power supplies that fit into the DSO-X oscilloscopes. A suitable model is the RPSG-160-12 from Meanwell. It is a 12V 160W power supply. The designation “G” in RPSG indicates that there is also a 5V standby supply. And it is exactly this function that the DSO-X needs. Because as described before, the front switch on the osci is not intended to disconnect the primary side of the mains supply, but only to switch a line on the DC low voltage connector to ground. This line controls the “PowerON pin” in the power supply.

Mechanically, the Meanwell almost fits on the mounting brackets of the DSO-X. “Almost” means that the distance between the mounting holes of the long side on the powersupply is about one millimeter further apart than the mounting bolts on the chassis of the oscilloscope. However, this can be quickly adjusted with a small round file or a 4mm drill bit. Now the Meanwell Powersupply can be attached to the oscilloscope chassis with the original Torx screws. The plug connection for the AC supply from the OSZI board to the power supply can be taken directly from the old power supply.

The 12V voltage supply at CN2 of the power supply is connected to pins 1,2,3,4 (+12V) and 5,6,7,8 (GND). The connection line to the oscillator must be adapted accordingly.

The picture below shows the pins of the connector strip on the oscilloscope labeled.

I re-pinned the wires to fit and connected the connector to the powersupply as shown below.

The main power supply to the oscilloscope is now established. Only the “power-on line” (PowerOn) is missing. For this I disconnected the 7th pin (GND) and the 9th pin (Switch) from the old connector and soldered them directly to the standby board of the power supply. The wire at the lowest pin of the standby board is the signal “PowerOn” and the one above is GND. So the power supply can be powered up with the front power switch on the oscilloscope.

“Control lines” for the PowerOn of the power supply unit

After a short function test and checking of the voltage (can be corrected if necessary also at the trim potentiometer at the power supply) the rebuilding is finished and the assembly can take place again.