Alle Beiträge von Ingmar Bihlo

Sony Video8 Walkman GV-8E

Sony GV-8E

Occasionally I browse flea market websites for vintage and retro devices from the 70s, 80s and 90s. If an absolute bargain is in sight, then I strike and sacrifice a few euros. This time I found a whole box of Sony portable media players. The whole thing just cost me the equivalent of a pack of Cafe. However, the state of the devices in terms of function is also unknown. A particularly beautiful piece (yes – that’s always in the eye of the beholder) from this box is the Videowalkman GV-8E from Sony. This is a portable, analog video player / recorder that has a VHF / UHF television tuner and an LCD monitor integrated in one device. While that may not be anything exciting today, the GV8E was a very nice and expensive piece of technology when it was launched in 1988. So the portable lands on my table and gets its 6V DC supply from the power supply. The disillusionment comes as quickly as the initial euphoria. The device shows no function despite the power supply being upright. It does not react to any key press, no LED lights up. (Somehow I was expecting this or something similar)

But the ambition is too great not to look inside the device and to look for the problem. I quickly started disassembling and roughly dividing the device into its components. The service documents can be found online, which are very helpful here.

GV8E in parts

After examining the block diagram of the entire system, the start of the troubleshooting was the DC / DC converter board. This board, covered by a shield plate, produces all the voltages required for the supply of the individual components from the 6V input voltage. A measurement on the test pins on the board showed that some voltages were missing. So there must be a problem here.

solder side of the DC/DC converter board
partside of the DC/DC converter boards

After removing the shield plate and inspecting the components, I noticed a defective 1.6A fuse (F103). This fuse protects the primary circuit of the switching converter. It can be seen from the plan that transistor Q114 was low-resistance and thus caused the fuse to trip.

extract from the circuit diagram of the DC / DC converter

The transistor is a 2SB1121 bipolar PNP transistor. Of course I didn’t have that in my collection. So thinned the component boxes for a suitable replacement …

replacement for the 2SB1121 is the PBSS5250Z

Then I found a PBSS5250Z, which has a slightly larger housing, but should do its job in the circuit.

defective Q114 desodered

Due to the larger design and the limited space available, I could only solder the replacement transistor upright.

Q114 renewed

Now a new fuse is still missing in the board. After installing and checking the other components in the affected circuits, the next function test was started. All boards electrically connected again and 6V connected to the battery terminals – and look – the Powersupply board starts up and the voltages are there. Now the GV8E can be switched on again with the power button, the LED also lights up and a quiet noise can be heard from the loudspeaker. However, none of the drive motors are running and the LCD monitor remains dark. The LED lights up briefly when the „Ejekt“ button is pressed, but the motor responsible for ejecting the cassette compartment does not start. That means -> continue searching for errors. First of all I will take a look at the LCD monitor. It is quickly removed and dismantled. All the less pleasing is the condition of the board. Here the „decaying“ electrolytic capacitors raged with their „body fluids“. (Of course this means the electrolytes)

Leaked electrolytic capacitors

The liquid electrolytes of the electrolytic capacitors have leaked over the years and have attacked the conductor tracks and also the solder joints. Sometimes it is so bad that small components, such as SMD transistors and resistors, fall off the board as soon as they are touched. At the latest now it is absolutely necessary to have the circuit diagram of the device at hand. Otherwise it will be difficult afterwards to correctly refill the missing parts. But first the old electrolytic capacitors had to be removed.

this is what the circuit board under the electrolytic capacitors looks like

With PCB cleaner I was able to remove the remains of the electrolytes and only then could I see the damage to the circuit board. Corroded areas had to be sanded with a glass brush and burned components had to be replaced. After cleaning again, the new capacitors (this time ceramic multilayer capacitors instead of the electrolytic capacitors) have found their place.

pcb with new parts

After this procedure the time had come. The next function test started. After reconnecting all plug connections and the power supply, there were further signs of life. The backlight (CCFL) started again and in the upper left corner it was „00:00“ to see the flashing clock of the on-screen display … Unfortunately, that was all. The OSD display was very blurry and the rest of the picture was white. The brightness controls did not respond. So the board had to be examined „big“.

The board of the LCD monitor still had many broken conductor tracks, which had to be laboriously repaired with individual strands and enamelled copper wire. There were also some SMD components (resistors and transistors) so corroded at their connections that only an exchange helped. The result looks a bit wild, but another function test was finally positive.

fixed displayboard

After I reassembled the monitor, I went to the drive. Here, too, I first checked or renewed all SMD electrolytic capacitors, as ALL of them had really leaked out. Fortunately, the circuit boards here were not so severely etched and can be easily cleaned. Then the function test came. And unfortunately there were still problems here. There was no cassette ejection and no reaction from any of the drives. After studying the service manual and measuring many supply voltages, I was able to identify a processor as a source of errors. It is a SONY CXP80116.

Sony CXP80116

This chip controls all drives, leds, queries sensors, etc. It is also responsible for ejecting the cassette compartment. It controls a driver IC (bridge) via pins 20 and 21, which in turn supplies the charging motor. And exactly the two outputs remained at 0V. When the „Eject“ button was pressed, only a few millivolts were measured instead of the 5V. So at first there was a suspicion that the driver IC has an error and is pulling down the outputs of the controller. So the outputs from the controller to the motor driver were separated and 5V directly connected to the motor driver input – and lo and behold, the loading motor was activated. So the problem is with the 80116. After some back and forth I was able to find one of these and exchanged it. Another test pleased me, because the cassette could be loaded again and the head drum started.

And the next problem already appeared. One of the two loading arms only drove half off and then got stuck. That means I also have to disassemble the mechanics of the drive. Said and done. Fortunately, it was only a small bolt that holds a drive lever. This had loosened and slipped out. So the problem was quickly resolved. Now I was finally able to do a function test again. And this time everything worked. The cassette was loaded, the head disk started, the tape was threaded and finally it could be played. After I had tested all functions, the GV-8E can be reassembled. Now he can go to the showcase as a „museum piece“;)

 

working again

 

Technical data of the GV-8E:

  • Video recording System: Rotierendes Zweikopf-Helical-Scan-FM System
  • Audio recording System: Rotierender Kopf, FM System
  • Videonorm: CCIR, PAL color
  • Kassettenformat: 8mm Videokassette
  • Bandgeschwindigkeit: SP: 2.0051 cm/s LP:1.0058cm/s
  • LCD Bildschirm: 6.2×4.6cm (3inch Diagonale)
  • Bildschirmtyp: TN LCD/TFT active Matrix mit 92.160 Bildpunkte
  • TV-Tuner: VHF Kanal 2-12, UHF Kanal 21-69
  • Anschlüsse: RF-Antenne, Video Input/ Output Chinch, Audio Input/Output Chinch (mono), Headphone 3.5mm Klinke
  • Energieversorgung 6V (Akku oder Netzadapter)
  • Leistungsaufnahme: 7.1W
  • Abmessungen: 129x67x213mm
  • Gewicht: 1.15kg ohne Akku
Typenschild des GV -8E

 

   Sende Artikel als PDF   

Read LCR meter via Matlab

LCR-Meter 4297A Agilent

In this post I would like to devote myself to something else. It’s not about retro technology, it’s about a little thing that makes working in the office/lab easier. One of the many measuring devices I deal with is an old Agilent LCR meter. As is known, the LCR Meter 4297A can be used to measure the inductance, capacitance, etc. of electrical components and generally of structures which are assigned to the electronics / electrical engineering sector. Roughly speaking, the 4297A actually only measures current / voltage, the phase relationship between the two and the energy direction. And at a certain frequency. All parameters such as L, C, R, X, Y, Q, PHI, … are then mathematically calculated and output from these parameters. The frequency here can be set from 1MHz to 3GHz (in 100kHz steps). Ideally, the measuring device can measure not only in one frequency point, but also in many. By „many“ is meant here that the measuring device can generate frequency tables with 32 entries. There are eight of these tables. This makes it possible to display the course of a measured variable in the form of a curve. However, this is quite cumbersome. The contents of the tables must be exported and saved manually (as „csv“ files) table by table. This means that each table must be selected individually. Then select the „Export List View“ dialog – then specify a storage path and file name. Only now are the first 32 records exported. This process must be repeated eight times in total. It is saved on a 3.5 inch floppy disc – the only available medium. You could also hang the 4297A optiona on a LAN and set up file sharing. However, manual export is not spared. The .csv files can now be opened on a „normal“ computer. They must then be put together manually in postprocessing. Only now can a diagram be made from the data. Here Matlab from Matworks is a good tool, which is often used in our laboratories as part of training.

NI GPIB – USB Controller

To simplify this cumbersome process considerably, I created a small script that communicates with the measuring device using the SCPI commands (Standard Commands for Programmable Instruments). That means: The measuring device is connected to a PC via a GPIB-USB controller. A Matworks Matlab installation including the required toolboxes is located on the PC. The Matlab script should now simply switch through the tables in sequence and read out the contents of the individual parameters and save them in an array. The content of the arrays is then displayed directly in a plot. However, this method only uses the contents of the tables. It would of course also be possible to set any desired frequency directly in a loop using the script, read out the measured values, select the next frequency, etc. This would max. Total 29990 points over the entire frequency range. The eight tables, each with 32 points, only allow 256 points. For now, however, that is sufficient and also much faster.

Transmission Line 50 Ohm termination resistor
line is terminated

The example shows the impedance curve (Z curve) of a 50 Ohm transmission line. The end of the line is terminated with a 50 ohm resistor. The frequency range is 1MHz to 3 GHz. The situation is different if the line is open or closed briefly. The electromagnetic wave is then not converted into thermal energy at the end of the line, as in the „matched“ system, but is reflected back into the system.

line is shortened

The following very simple Matlabscript enables the reading of the measuring device parameters. The script serves as an example of how to get the measurement data quickly. The programming manual of the manufacturer of the LCR meter lists all SCPI commandos and plenty of examples with which you can communicate with the measuring device.


%auslesen der agilent LCR Keule 4287A
%gekodet von ingmar bihlo Ende November 2017

%anschluss über gpib ni adapter
%LCR gpip adresse: 5
%%
%vorarbeiten an LCR Keule
%
% Es müssen 8 Tabellen mit je 32 Punkten definiert sein
% (power und average ist egal, wird nicht ausgelesen)
% die CALibration muss gemacht worden sein
% unter "measurement parameters" muessen vier parameter definiert sein
% zb. Z, qhi, R, L, etc... diese sind dann in den variablen param1 bis 4
% enthalten

%%

% gpib interface oeffnen und identifier lesen
g = gpib('ni', 0, 5);
g.InputBufferSize = 100000; % Set the buffer size
fopen(g);
fprintf(g, '*IDN?')
idn = fscanf(g);
fclose(g);

num1all=0; % initialisieren der variablen für den summenvector
num2all=0;
num3all=0;
num4all=0;
freq=0;

fopen(g);
%read list parameters (frequency points)
fprintf(g, ':SOUR:LIST?');
fpoint=fscanf(g);
listchar=strsplit(fpoint,',');
list=[cellfun(@str2num, listchar(:,1:end))]
clear listchat; clear fpoint;

%analyze list content
points=freq(1);

for i=1:8
%Tables selecten
fprintf(g, strcat(':SOUR:LIST:TABL 0',num2str(i)));
pause(1); %pause 1s zum umschalten der tabelle

%parameter1 abholen
fprintf(g, ':DATA:FDAT1?'); %parameter 1 anfragen
par1=fscanf(g); %parameter 1 holen

string1=strsplit(par1,','); %parameter 1 string nach komma zerlegen
%num1=[cellfun(@str2num, string1(:,1:end))] %parameter 1 strings in dec konvertieren
num1=[cellfun(@str2num, string1(:,1:end))];
num1all=[num1all,num1]; %parameter1 aktuell mit parameter1 aus vorherigem durchlauf concentenaten

fprintf(g, ':DATA:FDAT2?');
par2=fscanf(g);
string2=strsplit(par2,',');
num2=[cellfun(@str2num, string2(:,1:end))]
num2all=[num2all,num2];

fprintf(g, ':DATA:FDAT3?');
par3=fscanf(g);
string3=strsplit(par3,',');
num3=[cellfun(@str2num, string3(:,1:end))]
num3all=[num3all,num3];

fprintf(g, ':DATA:FDAT4?');
par4=fscanf(g);
string4=strsplit(par4,',');
num4=[cellfun(@str2num, string4(:,1:end))]
num4all=[num4all,num4];

%read list parameters (frequency points)
fprintf(g, ':SOUR:LIST?');
fpoint=fscanf(g);
listchar=strsplit(fpoint,',');
listraw=[cellfun(@str2num, listchar(:,1:end))];
list=listraw(:,2:end); %von pos2 das feld schreiben (an pos ist die anzahl der zeilen)

for c=1:3:96
freq=[freq,list(c)]; %von jedem 3. wert aus list ein neues array bilden
end

clear listchat; clear fpoint;

pause (1);
end

%%

%ausgabevariablen festlegen
frequency=freq(:,2:end);
param1=num1all(:,2:end);
param2=num2all(:,2:end);
param3=num3all(:,2:end);
param4=num4all(:,2:end);

%%
% Cell array richtig uma drahn
x1=param1(1:32);
y1=param1(33:256);
param1 = [y1 x1];

x2=param2(1:32);
y2=param2(33:256);
param2 = [y2 x2];

x3=param3(1:32);
y3=param3(33:256);
param3 = [y3 x3];

x4=param4(1:32);
y4=param4(33:256);
param4 = [y4 x4];
%%
%uerberflüssige variablen loeschen
clear c; clear i; clear list; %clear freq;
clear par1;clear par2;clear par3;clear par4;
clear string1;clear string2;clear string3;clear string4;
clear num1all;clear num2all;clear num3all;clear num4all;

fclose(g);

%plotten der ergebnisse
figure(1);
plot(frequency,param1);
grid on; hold on;
xlabel('Frequency [Hz]'); ylabel('Measurement Parameter1 |Z| [Ohm]');
title('Agilent LCR Keule');

figure(2);
plot(frequency,param2);
grid on; hold on;
xlabel('Frequency'); ylabel('Measurement Parameter2');
title('Agilent LCR Keule');

figure(3);
plot(frequency,param3);
grid on; hold on;
xlabel('Frequency'); ylabel('Measurement Parameter3');
title('Agilent LCR Keule');

figure(4);
plot(frequency,param4);
grid on; hold on;
xlabel('Frequency'); ylabel('Measurement Parameter4');
title('Agilent LCR Keule');
   Sende Artikel als PDF   

Cassette player/recorder SONY TC150B

Sony TC-150 cassette recorder

The Sony TC-150 is the newest, old member of the collection. Once again purchased as a defect device, this baby found a place in the workshop. After a quick inspection, it was immediately clear that the ravages of time were gnawing and, as is often the case, the drive belts became brittle or decomposed. Otherwise, the device is in perfect condition, hardly any scratches and damage to the case. The battery compartment was also clean. There are four belts of different lengths in the device.

belts to replace

Suitable replacement belts can be obtained, for example, from a large electronics store that is represented in Austria by six megastores. You will quickly find what you are looking for under the name „drive belt range“ and „1.1mm edge length“. Replacing the straps is less quick. Here you should take at least half an hour and carefully take the drive apart.

The main circuit board must be removed in order to access the pulleys or to be able to unscrew them further. However, this is only possible if some lines are unsoldered. Only then you can fold up the board. Once that’s done, you can unscrew the retaining plates above the pulleys. They form the backing of the flywheels (capstan shaft). On this occasion, it is advisable to check the capstan shaft for dirt (due to belt wear) and damage, or it should be cleaned. The pressure roller must not be neglected either. In this model, both were in great condition. The pinch roller was neither glazed and brittle, nor contaminated with tape wear or shrinked. So I could put on the new straps. The main belt from the engine is put on with a rotation of 90 °. Here you should note the installation position of the old belt, if it still exists, or at least do a short test run after fitting the new belt.

If everything turns again (and especially in the right direction) then the assembly can be done. Solder the wires again, screw the circuit board and the repair is done. To have this man a test cassette, here are some parameters, such as tape speed or the tracking of the tape head, which are given and adjusted if necessary.

the TC150 after belt replacement
the VU-meter for recording level control to as battery meter

 

Technical data of the SONY TC-150:

Vendor:                                    Sony
Type:                                         TC-150 (Europa) bzw. BT-50 USA
year of production:           ca. 1977 – 1982 (according to various sources)
Modell kind:                          portable  Cassette Corder
Hauptprinzip:                      NF-Audio
                                                     Magnetbandaufzeichung/Wiedergabe
tape speed:      4.8cm/s
heads:                                      1 recording-/playback head
                                                     1 earase head (Permanentmagnet)
semiconductors:                8 tranistors, 5 diodes, 2IC´s, 1 FET
Power          :                           Outputpower: max 360mW
                                                     Powerconsumption : max 9W
Supplyvoltage:                   battery 4×1.5V AA, or accupack BP28
                                                     12V Caradapter bzw. 6V 4W wallplug
operationtime:                    2.5h at continous recording
Speaker:                                 dynamic 5cm Lautsprecher
Abmessungen:                    174 x 29.5 x 113 mm (BxHxT)
weight:                                    ca. 769g

 

 

 

   Sende Artikel als PDF   

Mini-TV Broksonic

Broksonic CIRT-2097T

This beautiful, small, new piece of technology from the eighties has been added to my collection. It is a small tube radio receiver with radio part called CIRT-2097T from the manufacturer Broksonic (according to Internet research it is an US company). The device I received with the attribute „defective“ quite cheap on a flea market platform. So I thought, the risk can be taken and risk a repair attempt. What great things can not be broken – if it’s not just the picture tube.

inside the Broksonic

After a short functional test with the plug-in power supply, it soon became clear that nothing was working. No picture – no sound, no nothing. Since the device also has a battery compartment, I next wanted to try to feed the power via the battery terminals to see if there may already be a problem. And there it was already – the problem. The battery cover was almost impossible to get off, it held as glued. After some back and forth, I got the lid but then non-destructive and it revealed the cause of „jamming“ or better „gluing“. There were still batteries in the battery compartment (probably for 20 or more years). They were in a bad condition, totally corroded and leaked. In part, the outer coat of the cell was corroded and no longer available. Oh dear – I thought, hopefully the leaked dielectric did not move inside the unit and did damage there. There was nothing left for me to do but to disassemble and check everything. And then the evil manifested itself:

from leaked battery cells distroyed pcb

About a quarter of the TV board had come in contact with the battery fluid. And the stuff has done a great job, etched away almost all the traces and leads from components.

So I first tried with PCB cleaner to remove all the crystals and the rest of the battery juice to get a closer look at the damage. A few random measurements with the ohmmeter quickly showed that many traces were severed. So it did not help, the tracks had to be uncovered. Only then would a reasonable repair possible.

Rough cleaning with the brass wire brush

With a rotating brass wire brush, I then began to remove the etched areas, remove the remains of the solder resist and expose the copper traces.

Fine work with glass brush

After the rough preliminary work had the glass brush ran. Only with that it was possible to remove all paint and corrosion residues and finally expose the traces. A tedious job …

the exposed and repaired copper tracks

… but finally it was possible to uncover and repair all damaged areas. Some resistors and capacitors also had to be renewed because their leads were also in poor condition.

After the repair, a bump test could then be carried out – lo and behold, there was no further error and the device was working properly again. So I was able to protect the repaired area of ​​the board with solder varnish from renewed corrosion and reassemble the device.

 

 

 

 

Finally, here is an overview of the technical data:

vendor:                            Broksonic (US-Firma New York)
type:                                  CIRT-2097T
year of production:   ca. 1982
model:                               TV+FM Empfänger portable
receiverprinciple:       Superhet
screensize:                     2 Zoll SW Bildröhre
bands:                               AM, FM, SW (Radio), VHFI,VHFIII,UHF (TV)
                                              AM: 535-1605kHz
                                              SW:3200-9700kHz
                                               FM:88-108MHzTV:
                                               VHF Kanal 2-13(US), 2-12 (E)
                                               UHF Kanal 14-83(US),21-69(E)
supply:                               battery or accu, AC with adaper
supplyvoltage:              accu 6V, battery 6×1.5V AA
speaker:                           dynamic 16 Ohms speaker
outputpower:              150mW
dimensions:                  150x53x202 mm (BxHxT)
weight:                             ca 1.1kg

   Sende Artikel als PDF   

VFD clock with date, day of the week and sound

I received a new kit for vacuum fluorescence display from Günter (gr-pojects). Thanks a lot!

It is a clock with Type IV-11 vacuum fluorescent display tubes for hours, minutes and seconds, and an IV-18 tube for date display, and IV-3 for displaying the day of the week. The clock consists of a mainboard with power supply, CPU, MP3 module and driver blocks for the tubes. The time is set and synchronized via an externally connected DCF-77 receiver. Later, the board will be extended with a real-time clock circuit. The power supply for the entire circuit comes from a small plug-in power supply with 12V / 1.2A. The total power consumption is about 450mA. As a special feature, the clock has a small MP3 sound module with MicroSD card slot. This receives from the microcontroller via the serial interface every quarter of an hour a corresponding command to play an MP3 file. Thus the quarter of an hour is signaled with a „gong beat“, half an hour with two and three quarters of an hour with three „gong strikes“. At the full hour, the corresponding time is announced.

The entire circuit is built into an aluminum-acrylic housing. All fittings are milled and screwed. A video of the structure and the function can be seen below:

   Sende Artikel als PDF   

Philips „Sonate“ Philetta Euro280

Philips Philetta Euro 280 „Sonate“

In the years 1968 to 1970, the radio receiver was built with the inscription „Philetta Euro 280“ by Philips. It is a small multi-band receiver with transistor equipment. The type designation 12RB280 / 30 with the inscription „Sonata“ seems to be another version of this model. In any case, I have dug up the version „Sonata“ – once again from the depths of the Kellergefilde – and after superficial cleaning connected to the mains. Immediately after switching on, the scale illumination lights up and a loud 50 Hz hum can be heard from the loudspeaker. Increasing the volume level adds some noise. So switched to the FM band and searched for a station – and lo and behold, it works. Only the buzzing disturbs. Otherwise, the device works without any major problems. To find the cause of the humming, you begin with the troubleshooting as usual in the power supply.

entfernte Rückwand

The rear panel is quickly removed and the power supply unit, consisting of a, mounted on a support plate transformer including rectifier and filter capacitors removed. Now, without using the oscilloscope and the multimeter, you can immediately see where the ravages of time have left their mark. The two electrolytic capacitors do not look quite healthy anymore.

A quick measurement of the voltages brings certainty. The DC voltages have a decent ripple, which causes the „hum“. So the function of the electrolytic capacitors to smooth the DC voltage is no longer, or poorly, given. A measurement of the capacities confirmed that. So I renewed the capacitors.

Power supply with renewed capacitors

Immediately after switching on, even before I had the probe at the measuring points, a noise was heard without „humming“. The oscilloscope image now showed a clean DC voltage – almost no ripple. The receiver worked again very clean, without disturbing background noise. That was apparently the only mistake.

Technical information:

The main principle of the receiver is a superhet (according to the superposition principle) with an IF of 460/10700 kHz. The waveband of the receiver:

frequency scale
  • long wave
  • medium wave 1 (520-1400kHz)
  • medium wave 2 (1400-1600kHz)
  • shortwave
  • UKW

The output stage has a power of 3W, which is converted into sound energy in a dynamic loudspeaker with permanent magnetic excitation. The case is made of plastic and has the dimensions 43×17.5×10.5cm with a weight of 2.4kg. The receiver is supplied with 220V / 50Hz mains voltage.

 

 

   Sende Artikel als PDF   

Technology toys from the past – made of plastic

This article has nothing to do with electronics. In my retro-madness I was once again rummaging in the cellar of the parents‘ house and discovered there behind dusty jars of musty-smelling cardboard boxes with unknown content. So what was left to me to uncover and view the contents of these cardboard boxes? And what came out here were other boxes of the well-known toy manufacturer „LEGO“. Some very dusty original boxes of Lego-Technik models and old washing powder boxes, which were filled with many, many colorful Lego bricks and other stuff and unfortunately also garbage. Actually, I thought to myself, these many plastic parts I can throw in the trash, because that will not play my son safe. Everything smells like cellar and is dirty and the work, everything to clean and sort will certainly no longer hurt anyone. But on the other hand is the really old toy from the 70s and 80s – so over forty years old. And that is exactly mine again. 🙂 Things from my childhood and memories of it.

So packed everything and transported home. And then, in painstaking work, sorted everything once into colors and freed it from rubbish and lego-foreign parts. And now the real work began. The goal should be to put together from the many parts of the old Lego-Technik models and missing parts as far as still available to order. The „vintage kits“ should be restored as well as possible in their originality.

Well mixed and not complete Lego boxes

The photo shows a small part of the „excavated“ Lego boxes. At least the boxes were already roughly cleaned. What came out after the painstaking sorting and construction work, however, can also be seen again.

 

Nr. 853 Lego Car-Chassis

The number 853 is the car chassis. The kit was sold in the year 1977. It consists of 601 parts and finished construction about 52cm long and 22cm wide.

The model has a four-cylinder in-line engine with two-speed gearbox and cardan shaft to the rigid rear axle. The gearbox as well as the pistons are functional. Likewise, the steering works. The seats are displaceable in the longitudinal axis.

In this series, the rear axle was still rigid and equipped with a differential. The following picture shows the tidy, restored kit.

 

Nr.: 8860 Car Chassis

Out of 671 individual parts, the car is to assemble chassis number 8860. The set dates from the year 1980 and has a size of 46×19 cm. Here was compared to the 853er already much expanded. The rear wheels are hung individually and have a suspension. The engine sits behind and this time is a four-cylinder boxer. Again, there is a transmission with three stages.

The seats are adjustable in the longitudinal direction and the inclination of the seat back can also be adjusted. Again, a rack and pinion steering is installed.

The original packaging is still available and looks like this in the sorted condition:

 

Nr. 854 Lego GoKart

From 1978 comes the Lego GoKart No. 854. It has the dimensions of approximately 21 x 13cm and is composed of 206 parts. On realized functions there is a rack and pinion steering and a single-cylinder engine, with a functional piston. The rear axle is rigid and the shaft is connected via a transmission with the crank of the piston. According to data in the network, this model has now reached cult status, as it should be one of the first Lego-technology models ever. Here is the original packaging and especially the number 9 on the front still available, then the model in collector’s circles should be really valuable. Unfortunately, I can not meet either criterion.

Nr. 856 Lego Bulldozer

 

With the model no. 856, Lego has launched one of the countless construction vehicle models on the market. The bulldozer dates back to 1979 and consists of 370 parts. The base is 24x 11cm at a height of 14cm. Of the functions of the blade is tiltable, raised and lowered. Two chains on gears represent the connection to the bearing surface.

 

Unfortunately, here too, only the box without internal division is available from the original packaging.

 

Nr. 8848 Lego Unimog

The Unimog 8848 from the year 1981 measures just under 30x12cm at a base of 14cm. It consists of 398 parts. As a functioning technology here again the steering, the tilting cargo area, as well as a raised and lowered, and tiltable bucket available.

Unfortunately, the box is missing the interior, otherwise the model is complete. Apart from the here presented, complete kits are still some more available, but where unfortunately too many parts missing. But some flea market or online raid of lego parts will probably arise once again to complete these sets and to be able to fully incorporate them into a retrospective collection.

 

 

   Sende Artikel als PDF   

YouTube, and interesting technology favorites

This time, I’m not going to talk about a project or an „old equipment concept“, but would like to introduce some interesting users or their contributions from the YouTube portal. These are contributions from the field of computer, technology and science, which I personally like to look at.

First and foremost, I would like to mention the legend of modern computer history, which has fascinated me since my youth. The ComputerClub from WDR times with Wolfgang Rudolph and Wolfgang Back. The two moderators moderated the program Computerclub from the beginning of the 80’s to 2003 at Westdeutscher Rundfunk. In the topics, the two men are generally concerned with computers and peripherals, new developments in the field of electronics and present all sorts of things here. Many broadcast recordings are archived on YouTube, including by user janbras.

On 22 February 2003, the last broadcast was broadcast on WDR.

But the two protagonists have not given up the computer club and let him resurrect on July 24, 2007 on a German private broadcaster (NRW-TV).

However, the private broadcaster NRW-TV had to cease its operation in 2016 and so the program was Nr.186 recorded as the last in the studios of NRW.

But Wolfgang Rudolph has managed by fundraising to set up his own studio and now produces the CC2 from his private studio on his own.

In the background, a lot has changed, which confused the viewers and freaks a bit. Parallel to the broadcasts existed the page cczwei.de which was filled by both gentlemen. After 13.12.2016 suddenly a new page appeared. The new domain cc2.tv has been created. The now operates Rudolph alone. The domain cczwei.de continues to be operated by Mr. Back. He is assisted by Heinz Schmitz, who is now producing YouTube broadcasts with Mr. Back. Apparently, there were sufficient reasons for the gentlemen to part with years of community work. There never was an official explanation.

 

From the computer area, the guys from VirtualDimension report. They call their channel VD Hurrican and produce the formats: Virtual Worlds, Back in Time, Retroplay and On Site. The contributions are absolutely professional and mainly deal with home computers. With a lot of background information the old 8 and 16 Bit’er are presented here. Gameplay as well as fair reports and contributions from community events are also part of their repertoire. As an example here a link to the unboxing of an Amiga500 and its history. On the occasion of their 1000th subscriber on YouTube, they have published a 1000-subscriber special with a studio tour.

From the Australian continent, Dave Jones, also an inveterate technician, blogs. On his YouTube channel EEVblog, He also introduces electronic devices, explains their structure and operation. A special category in his channel are the so-called Mailbags. Here, Dave receives packages from people in the community who he opens in front of the camera and presents their content. This can be old computers and boards, or even new developments and prototypes of startups that are presented here.

 

A slightly different channel is that of an Englishman. He calls himself Photonicinduction and shows experiments with high performances. All sorts of appliances, such as vacuum cleaners, heating lamps, washing machines, loudspeakers, etc. are operated to the limit of their maximum performance data – and far beyond. The end of the device through destruction is the goal here.

 

 

   Sende Artikel als PDF   

X-Mas 2016

Merry Christmas to the visitors of the blog!

Now it is already two years, in which I feed the „technology and retro blog“ with contributions. Who would have thought that … By now some readers have strayed here and asked if I could introduce one or the other device here. Of course I will try to realize it if possible. Unfortunately, the rubric with the computers of the 80s is still empty. Here I still lack the „thread“, as I should process the whole – it floats me to every device before a small video in which the devices are to be shown in the living state. If someone has ideas for that … like.

I would like to say a big thank you to my colleague Mario Wehr, who provides me with the WordPress environment and thus offers excellent service!

In this sense: Merry Christmas and happy holidays!

 

 

 

   Sende Artikel als PDF   

Retro controller brand new

NES – Nintendo Entertainment System is certainly still a household name. It was the 8-bit game console from Nintendo, which was also sold in Europe in the mid-80s and had influenced the youth of the time. It is now a museum piece that already deserves the title „Retro“. Maybe for this reason, she begins to revive in the Retrogamergemeinde. For example, this year a remake of the NES in miniaturized form with modern technology and pre-installed games on the market.

dsc_2760Also via emulators for all kinds of platforms you can bring the old NES game titles back to life. In order to be able to serve these games „in the right way“ (of course, it is also possible with the PC keyboard or via the touch screen on the mobile phone), the company 8Bitdo Tech has launched the NES30 GamePad Controller. It is a wireless bluetooth controller which was modeled on the original NES controller. It is equipped with an integrated rechargeable battery that can be charged via a MicroUSB cable connection. The controller is designed to be configured as a PC game controller, as a joystick, as a Bluetooth keyboard, and as a USB joystick. This can be realized via five different modes. These modes can be selected by keyboard shortcuts during power up. The table below shows the different modes:

  Mode1 Mode2 Mode3 Mode4 Mode5
  Joystick BT-Keyboard iCade Emu-Touch USB-Joystick
Power ON START START+B START+A START+X Kabelverbindung
Blue LEDs are flashing 1x 2x 3x 4x
OS WIN Android WIN/Apple Android Android Apple Android Apple WIN
           

dsc_2759The picture shows the USB charging socket, to the right of which are two status LEDs.

dsc_2816The battery is located on the back of the board

dsc_2817die Platine des Controllers; der die Firmware des Mikrocontrollers kann aktualisiert werden

dsc_2818Contact mats represent the buttons. Under the two shoulder buttons are real micro buttons …

dscn0763Here is the emulator „NES Emu“ served on an Android phone with the NES30;)

 

   Sende Artikel als PDF